Full Electronics Bay for BT60 x 7 inch (Standard)
$27.95
Full electronics bay. (All that is required is an Altimeter and a Battery.) Fiberglass COUPLER NOT INCLUDED. ADD 7" Coupler. Choose BT 60 and Make 7"
Kit is easy to assemble and includes brass threaded inserts and screws for attaching everything in its place. 200 lb Kevlar attachment tags for attaching recovery. The switch is built in the bay cap. Wiring is included. Each cap is threaded to attach the provided charge canisters. Seriously all you will need is the altimeter and battery!
Weight: The bay weighs 8 1/4 ounces as shown in the assembled photo (the 9 volt battery is 1.7 ounces)
Choose the altimeter and you want to use in the dropdown below.
Note: Only fits Mach1 BT60 38mm XL couplers.
DOWNLOAD THE INSTRUCTIONS AT THE BOTTOM LEFT OF THIS PAGE
G10 Fiberglass 38mm (1.6") Bulkplate for nosecone (Glue on)
$2.50
Fits our standard 38 mm (1.6") Coupler and Nose Cone Coupler
G10 Fiberglass 54mm (2.2") Bulkplate for nosecone (Glue on)
$4.50
Fits our standard 54 mm (2.2") Couplers and Nose Cone Coupler.
G10 Fiberglass 65mm (2.6") Bulkplate for nosecone (Glue on)
$4.50
Fits our standard 65 mm (2.6") Coupler and Nose Cone Coupler
G10 Fiberglass 76mm (3") Bulkplate for nosecone (Glue on)
$5.00
Fits our standard 3" Coupler and Nose Cone Coupler
G10 Fiberglass 98mm (4") Bulkplate for nosecone (Glue on)
$6.00
Fits our standard 98mm (4") Couplers and Nose Cone Couplers
G10 Fiberglass 6" Bulkplate for nose cone (Glue on)
$8.00
Out of stock
Fits our standard 6" Coupler and Nose Cone Coupler.
G10 Fiberglass 54mm Nosecone Electronics Bulkhead (Removable Kit)
$17.95
Nose cone addition for mounting telemetry or event altimeters in the shoulder of a 54mm nose cone. Easily removable (just screws on and off). Also very useful When used with Mach 1 (and most other) new nosecones. In this system you do not glue in the shoulder coupler. It simply slides in and out, making it a breeze to add and subtract nose weight as well!
This system is a stronger way to mount your recovery Eye Bolt as well. All the stresses transfer to the tip. For this system to fail you would need to yank the threaded rod out of the tip, or rip the tip through the nose cone! Not happening!
All hardware and instructions included.
Kit Parts:
1- Screw on bulkhead. (With eyebolt attachment.
1- Glue in Bulkhead. (for centering rod)
1- GPO3 Sled
1- 1/4" Nickel plated Brass Sleeve (For mounting Sled)
1- 1/4" Threaded rod (not pictured)
All needed Nuts and washers. (Some, but not all pictured)
This system is a stronger way to mount your recovery Eye Bolt as well. All the stresses transfer to the tip. For this system to fail you would need to yank the threaded rod out of the tip, or rip the tip through the nose cone! Not happening!
All hardware and instructions included.
Kit Parts:
1- Screw on bulkhead. (With eyebolt attachment.
1- Glue in Bulkhead. (for centering rod)
1- GPO3 Sled
1- 1/4" Nickel plated Brass Sleeve (For mounting Sled)
1- 1/4" Threaded rod (not pictured)
All needed Nuts and washers. (Some, but not all pictured)
G10 Fiberglass 65mm (2.6") Nosecone Electronics Bulkhead (Removable Kit)
$19.00
1/4" G10 Stepped Fiberglass Bulkhead fits our 2.6" Nosecone Coupler. Designed to be used with our nosecones or any fiberglass nose cone with a removable tip.
Kit contains:
1 GPO3 Sled.
1 Brass or Nickle sled rail guide.
1 Bulkhead Electronics bay cover (preassembled)
1 Glue in bulkhead.
1 threaded rod (enough to reach from the tip to the bulkhead cover. (On 5:1 ogive, 4:1 ogive and 3:1 ogive cones)
1 Assembly Instructions.
Where the traditional shock cord mount mounted to a glue in bulkhead, this system transfers all stress to the tip. You would have to pull the tip through the cone for failure. (Not happening. Along with this added security the system also creates a space for Electronics to be easily mounted in the nose cone. Also (on new nose cones) the coupler is not glued in allowing easy access to the interior of the nose cone for adjusting nose weight.
Kit contains:
1 GPO3 Sled.
1 Brass or Nickle sled rail guide.
1 Bulkhead Electronics bay cover (preassembled)
1 Glue in bulkhead.
1 threaded rod (enough to reach from the tip to the bulkhead cover. (On 5:1 ogive, 4:1 ogive and 3:1 ogive cones)
1 Assembly Instructions.
Where the traditional shock cord mount mounted to a glue in bulkhead, this system transfers all stress to the tip. You would have to pull the tip through the cone for failure. (Not happening. Along with this added security the system also creates a space for Electronics to be easily mounted in the nose cone. Also (on new nose cones) the coupler is not glued in allowing easy access to the interior of the nose cone for adjusting nose weight.
G10 Fiberglass 76mm (3") Nosecone Electronics Bulkhead (Removable Kit)
$24.99
1/4" G10 Stepped Fiberglass Bulkhead fits our 3" Nosecone Coupler. Designed to be used with our nosecones or any fiberglass nose cone with a removable tip.
Kit contains:
1 GPO3 Sled.
1 Brass or Nickle sled rail guide.
1 Bulkhead Electronics bay cover (preassembled)
1 Glue in bulkhead.
1 threaded rod (enough to reach from the tip to the bulkhead cover. (On 5:1 ogive, 4:1 ogive and 3:1 ogive cones)
1 Assembly Instructions.
Where the traditional shock cord mount mounted to a glue in bulkhead, this system transfers all stress to the tip. You would have to pull the tip through the cone for failure. (Not happening. Along with this added security the system also creates a space for Electronics to be easily mounted in the nose cone. Also (on new nose cones) the coupler is not glued in allowing easy access to the interior of the nose cone for adjusting nose weight.
Kit contains:
1 GPO3 Sled.
1 Brass or Nickle sled rail guide.
1 Bulkhead Electronics bay cover (preassembled)
1 Glue in bulkhead.
1 threaded rod (enough to reach from the tip to the bulkhead cover. (On 5:1 ogive, 4:1 ogive and 3:1 ogive cones)
1 Assembly Instructions.
Where the traditional shock cord mount mounted to a glue in bulkhead, this system transfers all stress to the tip. You would have to pull the tip through the cone for failure. (Not happening. Along with this added security the system also creates a space for Electronics to be easily mounted in the nose cone. Also (on new nose cones) the coupler is not glued in allowing easy access to the interior of the nose cone for adjusting nose weight.
G10 Fiberglass 98mm 4" Nosecone Electronics Bulkhead (Removable Kit)
$29.99
Only a few left!
1/4" G10 Stepped Fiberglass Bulkhead fits our 4" Nosecone Coupler. Designed to be used with our nosecones or any fiberglass nose cone with a removable tip.
Kit contains:
1 GPO3 Sled.
1 Brass or Nickle sled rail guide.
1 Bulkhead Electronics bay cover (preassembled)
1 Glue in bulkhead.
1 threaded rod (enough to reach from the tip to the bulkhead cover. (On 5:1 ogive, 4:1 ogive and 3:1 ogive cones)
1 Assembly Instructions.
Where the traditional shock cord mount mounted to a glue in bulkhead, this system transfers all stress to the tip. You would have to pull the tip through the cone for failure. (Not happening. Along with this added security the system also creates a space for Electronics to be easily mounted in the nose cone. Also (on new nose cones) the coupler is not glued in allowing easy access to the interior of the nose cone for adjusting nose weight.
Kit contains:
1 GPO3 Sled.
1 Brass or Nickle sled rail guide.
1 Bulkhead Electronics bay cover (preassembled)
1 Glue in bulkhead.
1 threaded rod (enough to reach from the tip to the bulkhead cover. (On 5:1 ogive, 4:1 ogive and 3:1 ogive cones)
1 Assembly Instructions.
Where the traditional shock cord mount mounted to a glue in bulkhead, this system transfers all stress to the tip. You would have to pull the tip through the cone for failure. (Not happening. Along with this added security the system also creates a space for Electronics to be easily mounted in the nose cone. Also (on new nose cones) the coupler is not glued in allowing easy access to the interior of the nose cone for adjusting nose weight.
G10 Fiberglass 6" Nosecone Electronics Bulkhead (Removable Kit)
$38.99
Out of stock
1/4" G10 Stepped Fiberglass Bulkhead fits our 6" Nosecone Coupler. Designed to be used with our nosecones or any fiberglass nose cone with a removable tip.
Kit contains:
1 GPO3 Sled.
1 Brass or Nickle sled rail guide.
1 Bulkhead Electronics bay cover (preassembled)
1 Glue in bulkhead.
1 threaded rod (enough to reach from the tip to the bulkhead cover. (On 5:1 ogive, 4:1 ogive and 3:1 ogive cones)
1 Assembly Instructions.
Where the traditional shock cord mount mounted to a glue in bulkhead, this system transfers all stress to the tip. You would have to pull the tip through the cone for failure. (Not happening. Along with this added security the system also creates a space for Electronics to be easily mounted in the nose cone. Also (on new nose cones) the coupler is not glued in allowing easy access to the interior of the nose cone for adjusting nose weight.
Kit contains:
1 GPO3 Sled.
1 Brass or Nickle sled rail guide.
1 Bulkhead Electronics bay cover (preassembled)
1 Glue in bulkhead.
1 threaded rod (enough to reach from the tip to the bulkhead cover. (On 5:1 ogive, 4:1 ogive and 3:1 ogive cones)
1 Assembly Instructions.
Where the traditional shock cord mount mounted to a glue in bulkhead, this system transfers all stress to the tip. You would have to pull the tip through the cone for failure. (Not happening. Along with this added security the system also creates a space for Electronics to be easily mounted in the nose cone. Also (on new nose cones) the coupler is not glued in allowing easy access to the interior of the nose cone for adjusting nose weight.