Star Cruiser BT60 1.63" (38mmXL)
Total Length: 57"
Precision Slotted Booster: Filament Wound Fiberglass
Nose Cone: 38mm Plastic
Motor Tube: Filament Wound Fiberglass 29mm
Fins: 1/16 G10 Fiberglass Composite
Bulkheads and Centering Rings: 3/32 G10 Fiberglass Composite. G10 2-Piece Bulkhead Assembly
Deployment: Dual Deployment Capable. (See Below)
Recovery: Sold Separately (See Below)
Hardware: Mini Rail Buttons
Included Accessories: 1-4' #1500 Kevlar Attachment
Graphics: Add Holographic graphics for $18.00 Or Metallic Silver for $14.50 Choose Below
Recommended Motors: (G-J)
Not Included, But Recommended Hardware: Mach 1 Low Profile Retainer.
Go To Sim File Page
BT60 FIBERGLASS NOSE CONE WITH STEPPED ALUMINUM TIP
Sold out
Fits Mach 1 BT60 tubing. Separate, removable coupler and has stepped aluminum tip attached with a 10-24 screw and washer. Weight is 2.3 oz.
Specs: BT60 (38mm XL) 5:1 Ogive with Stepped Aluminum Tip
BT60 removable coupler. This is NOT a layup, gel coated nose cone.
About Our Compression Molded Nose Cones.
Compression molding is not necessarily a new concept, but our innovative process in composites, designed by an aerospace engineer, has taken the strength of fiberglass to a new level. The cone itself is a very strong single unit, and is highly compressed to get the maximum density and rigidity using the best resins and fiberglass available. Add to that, a stepped aluminum tip that eliminates “side slip” and you have one of the smoothest, strongest, most reliable nose cones in sport rocketry today!
NEW!! Mach1 Badass Multibay BT60
NOTE: All BT60 DD Rocket Kits come with a 7" coupler in the kit. (No need to buy one)
Kit is easy to assemble and handle in the field!
Included in Kit.
Sled that will carry the following Altimeters: (All on 1 Sled)
- EasyMini
- RRC2
- Stratologger CF
- Eggtimer Quantum
- Eggtimer Quark
- Raven
Predrilled Endcaps
9v Battery compartment
Stainless Steel Eye nut assembly
All threaded rods , nuts bolts and washers.
- Very easy to assemble and easy to use in the field.
- Brass Hi-pressure Charge well included.
- Screw switch with pre-installed connector and screw guide
- Stainless Steel Eyenuts
- Predrilled G10 1/8" Stepped Bulkheads
- 2 Brass Thumb Nuts for ease in the field
- Carries 6 Altimeters
- 9v Battery compartment and connector
- All rods, nuts and washers included. You only need a battery and altimeter!
Note: Only fits Mach1 BT60 38mm XL couplers.
1500# Kevlar Line By the foot.
1500lb Kevlar line for BT 60 and small 54mm Rockets. 72 cents per foot.
Top Flight Thin Mill Parachute 12"
Sold out
Top Flight Recovery's Thin Mill Rocket Parachutes are a great upgrade replacement for plastic parachutes. Pack very tight in smaller tubes!
- Light Weight
- Stronger
- Less Tangle
- More Durable
This Parachute will go easily in our BT20 and BT50 Rockets!
Also makes a great drogue!
Top Flight Thin Mill Parachute 36"
Top Flight Recovery's Thin Mill Rocket Parachutes are a great upgrade replacement for plastic parachutes. Pack very tight in smaller tubes!
- Light Weight
- Stronger
- Less Tangle
- More Durable
This Parachute will go in our BT60 Rockets! Good also for smaller 54mm Rockets
Stainless Steel Ball Bearing Swivel 320 lb (Pair)
320 lb Stainless Steel Swivel with Ball bearings (1Pair) 15 lb rockets and under.
Badass Fin Guide.3 Fin BT Size Kit. (All Four BT Size 3 Fin Guides)
Sold out
The Badass Build Guide fits fiberglass and paper sized body tubes. Easily the most useful tool to ensure everything is aligned and in place, it serves 3 crucial functions in your build:
All Four of the 3 Fin BT Guides. BT20 BT50 BT55 and BT60 3 Fin.
- Badass Fin Alignment - You don't need large expensive tools that look like they came out of the middle ages to get straight and square fins every time you build your kit. Slide the Badass Build Guide onto your body tube, secure your fins in each fin guide slot and your are done. No need to keep the rocket vertical while things cure and dry either. Since the Badass Fin Guide is so small, you can put your rocket on your rocket stand and continue working on other aspects of the kit while the fins cure. This is the easiest and fastest way to align your fins - even easier than “Just eyeballing it”!
- Badass Tube Marking - With this guide, you will get a perfectly straight and square line to mark around the tube for cut lines and minimum diameter fin placement. Place the end of the guide where you want to mark the tube and draw around it. Done! Additionally, mark center lines with precision. Each side has a notch at the front that is centered between the two fins. Mark where the notch is then use that to draw a line up your rocket. Now you know anything placed on that line is perfectly centered.
- Badass Drill Guide - Combined with your badass tube markings, you will have center drilled holes every single time. With the Badass Build Guide, your rail button holes and vent holes will not only be centered on the line but also always perpendicular to the body. To top it off, your drill bit will not skip or walk along the body tube as your drill! There are three sizes of drill guides: 1/16in, 3/32in, 1/8in.
Technical details:
These guides are modeled off Mach1 fiberglass tubing. The size of the tubes these were made to fit are below. These are meant to fit snug against the tube. Please make sure your tube within 1mm of the sizes below.
Badass Fin Guide. 3 Fin BT60 Single
Sold out
The Badass Build Guide fits fiberglass and paper sized body tubes. Easily the most useful tool to ensure everything is aligned and in place, it serves 3 crucial functions in your build:
- Badass Fin Alignment - You don't need large expensive tools that look like they came out of the middle ages to get straight and square fins every time you build your kit. Slide the Badass Build Guide onto your body tube, secure your fins in each fin guide slot and your are done. No need to keep the rocket vertical while things cure and dry either. Since the Badass Fin Guide is so small, you can put your rocket on your rocket stand and continue working on other aspects of the kit while the fins cure. This is the easiest and fastest way to align your fins - even easier than “Just eyeballing it”!
- Badass Tube Marking - With this guide, you will get a perfectly straight and square line to mark around the tube for cut lines and minimum diameter fin placement. Place the end of the guide where you want to mark the tube and draw around it. Done! Additionally, mark center lines with precision. Each side has a notch at the front that is centered between the two fins. Mark where the notch is then use that to draw a line up your rocket. Now you know anything placed on that line is perfectly centered.
- Badass Drill Guide - Combined with your badass tube markings, you will have center drilled holes every single time. With the Badass Build Guide, your rail button holes and vent holes will not only be centered on the line but also always perpendicular to the body. To top it off, your drill bit will not skip or walk along the body tube as your drill! There are three sizes of drill guides: 1/16in, 3/32in, 1/8in.
Technical details:
These guides are modeled off Mach1 fiberglass tubing. The size of the tubes these were made to fit are below. These are meant to fit snug against the tube. Please make sure your tube within 1mm of the sizes below.
8 oz High Strength Structural Epoxy Kit. With Chopped carbon Fiber
Sold out
Structural Epoxy. Kit. 4oz of Resin. 4oz of Curative, and 2 oz of 1/4" strand chopped Carbon Fiber.
- Mix 1:1 Ratio by volume
- Tensile Strength 7000 psi
- Flexural Strength 11,500 psi
- Gel Time 60 min
- Cure Time 72 hrs
- Great Bonding
Thick, but injectable. Great for internal and external fillets!