- BT 60 Kits
- >
- Chimera BT60
Chimera BT60
Diameter: BT60 (Made of Filament Wound Fiberglass) Precision Slotted
Total Length: 38.625"
Nose Cone: BT 60 5:1 Ogive Plastic. Upgrade to Fiberglass With Stepped Aluminum Tip
Motor Tube: Filament Wound Fiberglass: 29mm
Coupler Ebay Tube: 6.5 Inch Coupler Filament Wound Fiberglass
Electronics Bay:Add Electronics Bay
Fins: 1/16: G10 Fiberglass. CNC cut.
Bulkheads and Centering Rings: 3/32 G10 Centering Rings. G10 2-Piece Bulkhead Assembly
Deployment: Dual or Single Deploy
Recovery: Not Included
Hardware: 1-6' #1500 Kevlar Attachment
Included Accessories: 2 Rail Buttons
Graphics: Add $9.00 for Vinyl Graphics Below
Recommended Motors: E-I
Not Included, But Recommended Hardware: 29mm Retainer L
Now you can fly low power with a few less worries about crashes and wet weather. These BT sized G12 filament wound airframes with 1/16" G10 fins and G10 Centering Rings will be tough enough to take the punishment of many flights.
NEW!! Mach1 Badass Multibay BT60
NOTE: All BT60 DD Rocket Kits come with a 7" coupler in the kit. (No need to buy one)
Kit is easy to assemble and handle in the field!
Included in Kit.
Sled that will carry the following Altimeters: (All on 1 Sled)
- EasyMini
- RRC2
- Stratologger CF
- Eggtimer Quantum
- Eggtimer Quark
- Raven
Predrilled Endcaps
9v Battery compartment
Stainless Steel Eye nut assembly
All threaded rods , nuts bolts and washers.
- Very easy to assemble and easy to use in the field.
- Brass Hi-pressure Charge well included.
- Screw switch with pre-installed connector and screw guide
- Stainless Steel Eyenuts
- Predrilled G10 1/8" Stepped Bulkheads
- 2 Brass Thumb Nuts for ease in the field
- Carries 6 Altimeters
- 9v Battery compartment and connector
- All rods, nuts and washers included. You only need a battery and altimeter!
Note: Only fits Mach1 BT60 38mm XL couplers.
29mm Low Profile Retainer (Snap Ring Style)
Sold out
Machined Aluminum Motor Retainer. Fits Mach 1 29mm Motor tubes. Snap ring included.
Top Flight Thin Mill Parachute 30"
Only a few left!
Top Flight Recovery's Thin Mill Rocket Parachutes are a great upgrade replacement for plastic parachutes. Pack very tight in smaller tubes!
- Light Weight
- Stronger
- Less Tangle
- More Durable
This Parachute will go in our BT60 Rockets! Good also for smaller 54mm Rockets
Top Flight Thin Mill Parachute 9"
Sold out
Top Flight Recovery's Thin Mill Rocket Parachutes are a great upgrade replacement for plastic parachutes. Easily packs in a BT20 Airframe!
- Light Weight
- Stronger
- Less Tangle
- More Durable
Badass Fin Guide. 3 Fin BT60 Single
Sold out
The Badass Build Guide fits fiberglass and paper sized body tubes. Easily the most useful tool to ensure everything is aligned and in place, it serves 3 crucial functions in your build:
- Badass Fin Alignment - You don't need large expensive tools that look like they came out of the middle ages to get straight and square fins every time you build your kit. Slide the Badass Build Guide onto your body tube, secure your fins in each fin guide slot and your are done. No need to keep the rocket vertical while things cure and dry either. Since the Badass Fin Guide is so small, you can put your rocket on your rocket stand and continue working on other aspects of the kit while the fins cure. This is the easiest and fastest way to align your fins - even easier than “Just eyeballing it”!
- Badass Tube Marking - With this guide, you will get a perfectly straight and square line to mark around the tube for cut lines and minimum diameter fin placement. Place the end of the guide where you want to mark the tube and draw around it. Done! Additionally, mark center lines with precision. Each side has a notch at the front that is centered between the two fins. Mark where the notch is then use that to draw a line up your rocket. Now you know anything placed on that line is perfectly centered.
- Badass Drill Guide - Combined with your badass tube markings, you will have center drilled holes every single time. With the Badass Build Guide, your rail button holes and vent holes will not only be centered on the line but also always perpendicular to the body. To top it off, your drill bit will not skip or walk along the body tube as your drill! There are three sizes of drill guides: 1/16in, 3/32in, 1/8in.
Technical details:
These guides are modeled off Mach1 fiberglass tubing. The size of the tubes these were made to fit are below. These are meant to fit snug against the tube. Please make sure your tube within 1mm of the sizes below.
Badass Fin Guide.3 Fin BT Size Kit. (All Four BT Size 3 Fin Guides)
Sold out
The Badass Build Guide fits fiberglass and paper sized body tubes. Easily the most useful tool to ensure everything is aligned and in place, it serves 3 crucial functions in your build:
All Four of the 3 Fin BT Guides. BT20 BT50 BT55 and BT60 3 Fin.
- Badass Fin Alignment - You don't need large expensive tools that look like they came out of the middle ages to get straight and square fins every time you build your kit. Slide the Badass Build Guide onto your body tube, secure your fins in each fin guide slot and your are done. No need to keep the rocket vertical while things cure and dry either. Since the Badass Fin Guide is so small, you can put your rocket on your rocket stand and continue working on other aspects of the kit while the fins cure. This is the easiest and fastest way to align your fins - even easier than “Just eyeballing it”!
- Badass Tube Marking - With this guide, you will get a perfectly straight and square line to mark around the tube for cut lines and minimum diameter fin placement. Place the end of the guide where you want to mark the tube and draw around it. Done! Additionally, mark center lines with precision. Each side has a notch at the front that is centered between the two fins. Mark where the notch is then use that to draw a line up your rocket. Now you know anything placed on that line is perfectly centered.
- Badass Drill Guide - Combined with your badass tube markings, you will have center drilled holes every single time. With the Badass Build Guide, your rail button holes and vent holes will not only be centered on the line but also always perpendicular to the body. To top it off, your drill bit will not skip or walk along the body tube as your drill! There are three sizes of drill guides: 1/16in, 3/32in, 1/8in.
Technical details:
These guides are modeled off Mach1 fiberglass tubing. The size of the tubes these were made to fit are below. These are meant to fit snug against the tube. Please make sure your tube within 1mm of the sizes below.
1500# Kevlar Line By the foot.
1500lb Kevlar line for BT 60 and small 54mm Rockets. 72 cents per foot.
Stainless Steel M4 Eye Nut Kit (2 Pack)
Small Stainless Steel Eye Nut that is good for BT60 Rockets. Screws and washers included. (Fits perfectly through 1/8" Bulkplates.)
3mm Plastic Rivets (6 Pack)
6- Small 3mm Plastic rivets for connecting the Payload Tube to the Coupler AV Bay Tube on our BT sized Rockets.